Replace Lock in UPVC Door
If you have a Upvc door lock that isn't working properly, you must call a professional locksmith. They are quick, efficient and complete the job to a very high standard.
It's not difficult to alter a upvc bar lock. It's just a matter of knowing the procedure and follow the steps below.
Take off the barrel lock.
uPVC windows and doors are commonplace in a wide range of properties. They are excellent for letting natural light into the home and are simple to open using the right key. Switching the barrel of a lock on a uPVC door is a simple job that only takes five minutes. It's a quick fix if you have lost your keys, a tenant has left and not returned it or the barrel of the lock is damaged.
You'll need to take out the screws that hold the handles first. The handles will be removed of the way to allow access to the barrel screws for the lock. Be careful not to loosen the screws too fast because this could cause damage to the handles or cause them to fall off while you're working.
After the screws have been removed, look for the screw that holds the barrel lock in place on the inside of your door. It is a screw that stands out and is a different color than the screws on the door. Remove this screw by using the Phillips screwdriver. Take the key that you use to unlock the lock and then insert it into the barrel. Turn it as far to the right as you can. This will let the barrel go and make it easier to remove the door.
After loosening the screw, you can now break the pins that hold the Euro Cylinder. You'll require pliers that are strong or mole grips accomplish this. Grasp the protruding portion of the euro Cylinder and bend it up and down and from side to side. This will break the support pins that hold it in place.
Installing the new cylinder can be done after the old one was removed. The first step is to measure the size of the lock cylinder to ensure that you have ordered the right replacement. This can be done by measuring the distance between the middle of the circular keyhole and the middle of the square spindle. The measurement should be taken from the upper spindle.
Change the Cylinder
The main locking mechanism is an euro cylinder. It is easy to replace and doesn't require a locksmith or handyman. In fact, if the lock you have isn't antisnap or antibump, it should be changed to one with this protection built in. They're inexpensive and could help you save money and time in the event that your locks are compromised.
Open the door and stand directly in the front. This will allow you to easily reach the screws that hold the handle by hand or with the appropriate tool. You can loosen this screw a little maybe a quarter-turn to begin.
The cylinder will now be easily removed, as the screw will stop holding it in position. Next, you'll need to decide on the size of replacement cylinder that you need. There are about 25 sizes available. It is a good idea to bring your old cylinder along when you purchase a new one, so you are sure it will fit.
If you're not sure of the size, measure from the screw hole center to the cylinder's end. Repair My Windows And Doors is the only way to be sure you're getting the right size cylinder for your upvc doors.
Once you have the replacement cylinder ready, insert it into your door in reverse order to the way you removed the old one. Aligning the lock cam could be tricky, but it is typically a matter of alignment.
Now you will need to insert the long securing screws. Once this is done you can test the new cylinder and ensure that it is secured inside the door. Then, you can reconnect the handle to the door and test it again. If everything is functioning properly the cylinder lock on your door made of upvc has been replaced and you have added an extra layer of security to your home.
Change the Handle
There are a variety of reasons the door handle or knob for the door can become loose. This can be due to wear and tear on the handle itself or it could be due to the square spindle inside the handle getting worn out or loose from excessive force or use. In this instance, the door handle will need to be replaced.
It is essential that the door be opened so that it will not close between taking off the handle and replacing it. Remove the screws from the interior surface of the plate using a screwdriver. This will release your handle from the plate. Be careful not to lose these screws as they will need to be re-screwed back into place later.
It is now possible to remove the handles to access the cylinder lock within the door. The cylinder lock will be round or bulb-shaped, and is only used for multi-point locks for upvc and some aluminum doors. The procedure of changing the cylinder is similar to the process of changing the handle however, you'll have to remove the old cylinder from the door, and replace with a new one.
When selecting the replacement handle, it's important to think about the size. The handle should be the same size as the original because it will have to fit into the screws that hold the handle in place. A good place to start is by using a size matrix which will provide the standard sizes of replacement handles along with their keyhole center to handle plate distance.
Consider changing your handles for your upvc doors to a higher security standard like a Sold Secure SS301 set or 2* Kitemark security handles. This will increase the security of your home, as well as making it much easier to operate the door. These sets are a bit more expensive but the added security and peace of mind is worth the cost. To constantly push the door handle up and down in order to shut and open it is not something you want to be doing.
Change the Lock
The lock on your uPVC can be a vulnerable point for burglars. Upgrade your uPVC to multipoint locking to make it more secure. This would include an open hook as well as deadbolts to ward off burglars. You can employ an expert locksmith to assist you, but you could also do it yourself. The process is simple and simple. You will only need a few simple tools.
The first step is to loosen the screws that hold the handle in place. Using a screwdriver, you can take the screws off and place them in a secure place. Then, you can lift the handle and expose the screw that is holding the cylinder in position. The screw can be removed and replaced with a new one. Make sure the screw is of the same size as your original. It will need to be aligned correctly with the barrel of the lock.
Changing the lock on your uPVC door can be a bit daunting. You depend on it to secure your home, and mistakes could leave you without a way to open the door. However, if you know how to accomplish it, the procedure is fairly easy and is much less expensive than hiring a locksmith.
To change the lock on your uPVC door, you will have to open the inner faceplate of the lock. You will need to be able to see the screw that is located inside the door, as well as the bolt that holds it on the outside of the door. Once you have these screws in your hands, you can remove and replace the faceplate.
It is possible to replace the lock of your uPVC door for a variety of reasons. It could be due to a lost key, a tenant moved out and did not return keys, or you want to increase the security of your home.
The process of changing a uPVC lock could be accomplished by anyone with basic DIY skills. You will need to inspect the hinges inside the mechanism, which could be a difficult task in the event that the lock is stuck. If the hinges are lubricated, it should be simple to repair. If you are not confident, it is best to consult a professional.